Large Venue Classroom Interactive Conference. Find a Projector. Classroom Interactive Portable. Throw Calculator. Jump to B Moving the projector with cables still attached can damage the cables, which could cause fire or electric shocks to occur.
B Failure to observe this may cause the projector to become unbalanced and fall, which could result in damage or injury. Do not short-circuit, heat or disassemble the batteries or place them into water or fire. B Failure to observe this may cause the batteries to overheat, leak, explode or catch fire, and burns or other injury may result. B If the batteries are inserted incorrectly, they may explode or leak, and fire, injury or contamination of the battery compartment and surrounding area may result.
B If incorrect batteries are used, they may explode or leak, and fire, injury or contamination of the battery compartment and surrounding area may result. B You could fall or the projector could break, and injury may result.
B Be especially careful not to let young children stand or sit on the projector. Disconnect the power cord plug from the wall outlet as a safety precaution before carrying out any cleaning. Ask an Authorized Service Center to clean inside the projector at least once a year.
B If dust is left to build up inside the projector without being cleaned out, it can result in fire or problems with operation. B It is a good idea to clean the inside of the projector before the season for humid weather arrives. Ask your nearest Authorized Service Center to clean the projector when required. Please discuss with the Authorized Service Center regarding cleaning costs. We are constantly making efforts to preserve and maintain a clean environment.
Please take non repairable units back to your dealer or a recycling company. It also contains lead in some components. Disposal of these materials may be regulated in your community due to environmental considerations. Check that all of the accessories shown below have been included with your projector. Avoid setting up in places which are subject to sudden temperature changes, such as near an air conditioner. If installing the projector to the ceiling, ask a qualified technician to carry out all installation work.
You will need to purchase the separate installation kit Model No. Furthermore, all installation work should only be carried out by a qualified technician. Refer to page Draw curtains or blinds over any windows and turn off any lights near the screen to prevent outside light or light from indoor lamps from shining onto the screen. If the surface of the lens becomes dirty from fingerprints or anything else, this will be magnified and projected onto the screen.
Moreover, when not using the projector, retract the lens and then cover it with the lens cover. Do not apply any volatile substances which may cause discoloration to the screen, and do not let it become dirty or damaged.
The lamp may need to be replaced earlier due to variables such as individual lamp characteristics, usage conditions and the installation environment, especially when the projector is subjected to continuous use for more than 10 hours or the power is frequently turned on and off. B Do not project the same image for long periods of time, as this may remain as an afterimage on the liquid crystal panel. B The liquid crystal panel of the projector is built with very high precision technology to provide fine picture details.
Occasionally, a few non-active pixels may appear on the screen as fixed points of blue, green or red. Please note that this does not affect the performance of your LCD. Shift lever page This can be used to connect a commercially-available theft-prevention cable manufactured by Kensington. This security lock is compatible with the Microsaver Security System from Kensington.
This connector is used to connect a personal computer to the projector in order to control the projector externally. RSC compatible. This connector is used to input video signals from a video equipment such as a video deck.
This indicator illuminates red when the main power is switched on standby mode , and it illuminates green when a picture starts to be projected. This indicator illuminates when it is time to replace the lamp unit.
It flashes if a circuit abnormality is detected. This indicator illuminates if an abnormally high temperature is detected inside the projector. If the temperature rises above a certain level, the power supply will be turned off automatically and the indicator will flash. This button is used to accept and to activate items selected in the on-screen menus.
MENU button page This button is used to display the menu screen. When a menu screen is being displayed, it can be used to return to a previous screen or to clear the screen. INPUT select buttons page These buttons are used to switch the input signals from the connected equipment. These buttons are used to operate the devices which have been programed into the remote control unit using the preset or learning functions of the remote control unit.
When a menu screen is being displayed, this button is used to return to a previous screen or to clear the screen. M Cinema Color Management button page This button is used for aspect adjustment vertical and horizontal proportions. This button is used to reset the projector adjustment values to the factory default settings.
The selected device is displayed at the upper side. The setting guide for the preset and learning functions and the button operation guide for the selected device are displayed at the lower side. In way of installing projector, any one of the following four projection methods are used.
Select whichever projection method matches the setting-up method. Refer to page 52 for details. B Do not set up the projector vertically or tilted horizontally, otherwise it may cause damage to the projector. This projector can be placed in various places by controlling the shift lever at the front side of the projector to move the lens in order to adjust the position of the projected image.
BWhen the lens has been shifted fully to the right or left, you will not be able to shift the lens up or down. When the lens has been shifted fully up or down, you will not be able to shift the lens to the right or left. BGenerally, the maximum picture quality is obtained when the lens is moved to the center horizontally and vertically.
BWhen the projector is tilted vertically and keystone correction needs to be carried out, place the projector so that the center of the lens and the center of the screen vertical are matched. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the product.
If you need to use higher voltages or currents than this, you will need to obtain a separate V power cord. If you use the accessory cord in such situations, fire may result.
Address: One Panasonic Way Secaucus New Jersey Telephone number: View-PTV This device complies with Part 15 of the FCC Rules, Operation is subject to the following two conditions: 1 This device may not cause harmful interference, and 2 this device must accept any interference received, including interference that may cause undesired operation.
Do not remove the grounding pin on the power plug. This plug will only fit a grounding- type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact an electrician. Do not defeat the purpose of the grounding plug. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna.
Any unauthorized changes or modifications to this equipment will void the users authority to operate. Add page 3 to Favourites. BDo not continue to use the projector in such cases, otherwise fire or electric shocks could result. BCheck that no more smoke is coming out, and then contact an Authorized Service Center for repairs. BDo not attempt to repair the projector yourself, as this can be dangerous. Do not install this projector in a place which is not strong enough to take the full weight of the projector.
BIf the installation location is not strong enough, it may fall down or tip over, and severe injury or damage could result. Installation work such as ceiling suspension should only be carried out by a qualified technician. BIf installation is not carried out correctly, there is the danger that injury or electric shocks may occur. If foreign objects or water get inside the projector, or if the projector is dropped or the cabinet is broken, turn off the power and disconnect the power cord from the wall outlet.
BContinued use of the projector in this condition may result in fire or electric shocks. BContact an Authorized Service Center for repairs.
Do not overload the wall outlet. BIf the power supply is overloaded for example, by using too many adapters , overheating may occur and fire may result. Do not remove the cover or modify it in any way. BHigh voltages which can cause fire or electric shocks are present inside the projector. BFor any inspection, adjustment and repair work, please contact an Authorized Service Center.
Clean the power cord plug regularly to prevent it from becoming covered in dust. BIf dust builds up on the power cord plug, the resulting humidity can damage the insulation, which could result in fire. Pull the power cord out from the wall outlet and wipe it with a dry cloth. BIf not using the projector for an extended period of time, pull the mains plug out from the wall outlet.
Add page 4 to Favourites. If you look directly into this light, it can hurt and damage your eyes. BBe especially careful not to let young children look into the lens.
In addition, turn off the power when you are away from the projector. Do not place your hands or other objects close to the air outlet port. BHeated air comes out of the air outlet port. Do not place your hands or face, or objects which cannot withstand heat close to this port, otherwise burns or damage could result.
Replacement of the lamp unit should only be carried out by a qualified technician. BThe lamp unit has high internal pressure.
If improperly handled, explosion might result. BThe lamp unit can easily become damaged if struck against hard objects or dropped, and injury or malfunctions may result. When replacing the lamp, allow it to cool for at least one hour before handling it. BThe lamp cover gets very hot, and contact with it can cause burns. Before replacing the lamp, be sure to unplug the power cord from the wall outlet. BElectric shocks or explosions can result if this is not done.
CautionDo not cover the air inlet or the air outlet. BDoing so may cause the projector to overheat, which can cause fire or damage to the projector. BDo not place the projector in narrow, badly ventilated places such as closets or bookshelves. Do not set up the projector in humid or dusty places or in places where the projector may come into contact with smoke or steam. B Using the projector under such conditions may result in fire or electric shocks. When disconnecting the power cord, hold the plug, not the cord.
BIf the power cord itself is pulled, the cord will become damaged, and fire, short-circuits or serious electric shocks may result.
0コメント